Maytech GPS & IMU Remote MTSKR26WF V5.0 IP68 Waterproof Remote with for Efoil DIY Foil Assist Jetboard
Related Products:
If you want to use other cheaper but slower shipping method, please contact shelly@mayrc.com
Shipping time by DHL or UPS is fast, normally 3-7 days arrive to you.
> Get E-Manual: MTSKR26WF V5.0 Quick Start Manual
> Check Video Using Instruction
Specification:
| Model No | MTSKR26WF V5.0 |
| Upgraded Function |
Equipped with GPS (GPS Speed, Distance, Max Speed, Average Speed) Equipped with Tilted protection (IMU tilt sensor), protection angle can be adjust to 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall. |
| Waterproof Rank | IP68 double waterproof |
| Thr Mode | ESURF (SF) and ESK8 (SK) |
| 3 Speed Modes | With, adjust throttle % from 20-100% |
| Power Modes |
2 levels, Eco (Level 1) & Pro (Level 2) optional Signal strength: Pro > ECO Power Consumption: PRO > ECO |
| Throttle Lock | Yes, 10-120s optional |
| Signal Format | Support Standard PWM (PPM) and UART, output range from 10%-20%, which correspond to ESC/VESCTOOL Compatible controller throttle output range from 0%-100%. |
| PWM Signal Output Range |
In Esk8 mode: 1.5ms is stop position, 1.5-1ms for brake or reverse (upper trigger), 1.5-2ms for throttle (bottom trigger) In Esurf mode: 1-2ms for throttle (bottom trigger), no brake or reverse |
| Double Source Power Supply | Accept 5V power by ESC built-in BEC or extra 5V power |
| Output Signal Voltage | Max 3.3V |
| Display Parameters |
GPS Speed / Distance / Max Speed / Average Speed |
| Safety Button | Support |
| Cruise Control | With in Esurf Mode |
| Brake | With in Esk8 Mode |
| Accessories | Wirelss charging pad / Receiver / USB cable / Wristband / 1pcs 3 pins cable / 1pcs UART cable |
| Compatible Controllers | VESC/ Focbox/ Other PWM ESCs that has same signal output range with the remote. |
| Application | foil assist system, electric propulsion, underwater thruster, electric outboard, Esurf, Efoil, electric hydrofoil, electric surfboard, electric skateboard/ elongboard/ mountainboard, electric paraglider, etc., |
Updated functions:
- Add 3 speed modes options: you can adjust max throttle % from 20%-100%, good option for beginners.
- Stronger signal and strength optional: Remote and receiver signal strength is enhenced to avoid some signal interference nearby. With 2 levels signal strength: ECO and PRO. ECO signal is better emergy saving, can work longer time for each full charing. PRO is stronger signal.
- Better waterproof performance.
- Compatible with Maytech new MTSF300A-WP32 ESC: Could compatible with Maytech new small MTSF300A-WP32 ESC and can display voltage, current, temperature, etc parameters
- Display Voltage in %
- Throttle Lock Function: you can set lock time from 10-120s, safer to use.
- Equipped with GPS (GPS Speed / Distance / Max Speed / Average Speed)
-
Equipped with Tilted protection (IMU tilt sensor), protection angle can be adjusted to 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall.
IMU degree can be calibrated according to the receiver position to be placed on your board.
And Tilt protection can be turned off for experienced users.
Notice of usage:
- The terminal of the receiver must be lead out of water to ensure signal is stable, if you need to put the recever below the water surface, suggest to order 1m / 3m antenna to lead signal out of water surface.
- Receiver is not waterproof, if receiver need to be placed underwater, do good waterproof protection for receiver.
-
In order to avoid being corroded by sea water and to extend the remote life, please wash the remote in fresh water after using;
-
Make sure remote is fully dried when charge for it, do not leave the remote on charging pad when it's fully charged, please remove in time.




Parameters display in different Data Source and Throttle Mode:

Wiring Instructions when work with different ESCs/VESC:
1. If you use MTSF160A-WP32/ MTSF300A-WP32 / MTSF300A-WP32-HV / MTSF300A-WP32-HVPRO ESC, please refer to below wiring diagram:

2. If you use VESC controllers based on V4.12 / V6 / V75_300, please refer to below wiring diagram:

3. If you use OPTO ESC (without built-in BEC), please refer to below wiring diagram:

4. If you use MTSF300A-WP / MTSF500A-WP or other ESCs with built-in 5V BEC, refer to this diagram:

The remote has 2 Modes, signal output pulse width is different in 2 modes:
- Esurf Mode is 1ms-2ms, no stop no brake, if you use Esurf mode to work with VESCTOOL compatible controller, please use below settings in VESCTOOL and to match with the remote:
PPM Control Type: Current no reverse
PPM Mapping: Pulselength Start: 1.1ms; Pulselength End: 1.9ms; Pulselength Center: 1.5ms
Or you can use wizard mode to detect compatible value.

- Esk8 Mode is 1.5ms-1ms (Brake), 1.5ms-2ms (Speed up), 1.5ms is stop position.
Please noted to match compatible parameters for different modes in VESC_TOOL.
