Skip to product information
PPM Control Type: Current no reverse
Clearance Sale Maytech MTSKR1905WF V2.0 Waterproof Remote for Efoil Hydrofoil Foil Assist Board
$76.40 USD
Sale price
$76.40 USD
Regular price
Related Products:
If you want to use other cheaper but slower shipping method, please contact shelly@mayrc.com
Shipping time by DHL or UPS is fast, normally 3-7 days arrive to you.
Difference of V2.0 MTSKR1905WF and V5.0 MTSKR26WF:
|
MTSKR26WF V5.0 VS MTSKR1905WF V2.0
|
|||
|
Item
|
MTSKR1905WF (V2.0)
|
||
|
GPS Tracking Function
|
With
Can record distance, max speed, average speed
|
Without
|
|
|
IMU (Tilt Sensor) Function
|
With
Can set 30°/45°/60° tilt degree of your board in case of flipping over, separation of the rider from the board, or an accidental fall.
IMU degree can be calibrated according to the receiver position to be placed on your board.
|
Without
|
|
|
Waterproof Rank
|
IP68 Waterproof with 2 Layers Nanometers Coating, both on PCB board and screen
|
||
|
Application
|
Electric surfboard, Electric skateboard
|
||
|
Max Speed Set
|
With 3 speed modes, can set max throttle from 0%-100%, good for beginners
|
||
|
Display Screen
|
GPS Speed / Distance / Max Speed / Average Speed
Tilt sensor degree
RPM+Current+Temp+Volt+Speed+Distance(When work with VESC and MTSF-WP32 series ESCs)
Remote & Battery Power; Battery Remain %;Throttle Percentage; Signal Strength; |
RPM+Current+Temp+Volt+Speed+Distance(When work with VESC and MTSF-WP32 series ESCs)
Remote & Battery Power;
Battery Remain %;
Throttle Percentage;
Signal Strength;
|
|
|
Signal Strength
|
ECO (Level 1) and PRO (Level 2) Options;
PRO > ECO |
Only Level 0
|
|
|
Throttle Lock Function
|
With, 10-120s
|
||
|
UART
|
With TX and RX port
|
|
|
|
Double Source Power Supply
|
Accept 5V power by ESC built in BEC or extra 5V power
|
||
|
Firmware Updatable
|
Yes
|
||
|
Relay Swtich
|
Without
|
With
|
|
|
Control Pump
|
Without
|
Yes (Relay Switch) on receiver
|
|
|
Control Light
|
Without
|
Yes (Transistor Switch)
|
|
|
Set Safety Button
|
Yes
|
|
|
|
Brake Button
|
With brake in Esk8 Mode (Upper Trigger)
|
||
|
Bidirectional Control
|
Support, can control forward and reverse if your ESC with bidirection
|
||
|
Cruise Control
|
With in Esurf Mode
|
||
|
Wireless Charging
|
Yes
|
||
|
Accessories
|
Charging Pad; wristband; Receiver; UART and 3 pins cables
|
||
Updated functions:
- Add 3 speed modes options: you can adjust max throttle % from 20%-100%, good option for beginners.
- Stronger signal and strength optional: Remote and receiver signal strength is enhenced to avoid some signal interference nearby. With 2 levels signal strength: ECO and PRO. ECO signal is better emergy saving, can work longer time for each full charing. PRO is stronger signal.
- Better waterproof performance.
- Compatible with Maytech new MTSF300A-WP32 ESC: Could compatible with Maytech new small MTSF300A-WP32 ESC and can display voltage, current, temperature, etc parameters
- Display Voltage in %
- Throttle Lock Function: you can set lock time from 10-120s, safer to use.
> Get E-Manual: Remote Manual and Instruction
> Check Video Using Instruction
Click Here: How to Display Volt, Current, RPM with TX and RX?
Parameters display in different Data Source and Throttle Mode:
If you use MTSF160A-WP32/ MTSF300A-WP32 / MTSF300A-WP32-HV / MTSF300A-WP32-HVPRO ESC, please refer to below wiring diagram:
If you use VESC controllers based on V4.12 / V6 / V75_300, please refer to below wiring diagram:
If you use MTSF130A-WP32 / MTSF300A-WP / MTSF500A-WP or other ESCs, refer to this diagram:
The remote has 2 Modes, signal output pulse width is different in 2 modes:
- Esurf Mode is 1ms-2ms, no stop no brake, if you use Esurf mode to work with VESCTOOL compatible controller, please use below settings in VESCTOOL and to match with the remote:
PPM Control Type: Current no reverse
PPM Mapping: Pulselength Start: 1.1ms; Pulselength End: 1.9ms; Pulselength Center: 1.5ms
Or you can use wizard mode to detect compatible value.
- Esk8 Mode is 1.5ms-1ms (Brake), 1.5ms-2ms (Speed up), 1.5ms is stop position.
Please noted to match compatible parameters for different modes in VESC_TOOL.
If your surrounded has strong magnetic interference, the signal might easy get lost, suggest you order the version with 1m or 3m extend antenna.
Tips After Using:
In order to avoid being corroded by sea water and to extend the remote life, please wash the remote in fresh water after using; Also please charge when the remote all dry.
Related Products:
Foil Assist Kits:
